Search results

Most likely, yes. Maybe not if you go regular kit instead of HD, and only go with the 1 mm spacing.

Is the bed lined? Many have seen the plug for the panel in the bed not connected after a spray in liner is installed. Worth a shot.

It changes the location of the pivot to closer to the center of the leaf. Think of lifting a gallon of milk with your arms extended all the way, then doing it again with your arms closer to your body. Not at all a scientific explanation, but hopefully easy enough to understand.

I'm running the same kit on my long bed powerboost, and it's been flawless. No noises, and it's a game changer for me. How did you set yours up? I went with the 3rd hole, and both the white and black spacer (3 mm). It did lift the truck up a good 1½"-2", but my bed is normally loaded down daily...

I have read that it works, yes. I will be tackling this myself when I can find a deal on the mirrors and door panel with the power folding button. You'll also need to program it in forscan to work.

For $1500 a pair, I'd swap my non power mirrors tomorrow. People have been paying almost twice that for the retrofit thus far

I activated mine. I also use my phone as a hotspot occasionally (Verizon), but I find it much easier to just have it ready versus pulling my phone out, waiting for it to enable, and then watching my battery drain like crazy. I use a laptop, iPad, and occasionally let co workers sync their...

Now I'm curious. Mine used to be in the center as well, but it never came back. I was going to read the manual again to try and figure it out, but in my truck, turning off lane centering doesn't switch the view back to the speed, it just turns off the green lines and still shows a truck on a...

Since my dealer was no help, I figured I'd experiment myself. I bought this soft starter, and low and behold, it fixed my problem! They offer a few models, but I figured the 20 amp 120V would fit my needs since the 240V model was sold out. You can even program it to ramp anywhere from half a...

Still a sync 3.

Unfortunately, it looks like we got the short end of the stick on this. Here is the plug for the trailer mounted camera and TPMS setup on the F250 super duty equipped with the ultimate tow camera package. There are 7 wires populated on the connector, with an extra wire dangling next to it...

I got word from my dealer over the weekend on the issue I was having with my pro power. To summarize, I'm in the same boat as the OP, my truck (7.2 kWh) runs everything just fine, but one tool in particular turns off the generator every time, instantly. No breakers trip, the pro power just...

I tow 9,000-12,000 pounds occasionally, moving around small machines on steel flatbeds. I don't use a WDH, mainly because the trailers are all setup with pintle hitches and there is no WDH for pintle setups. If it were an issue, I suppose we could send the trailers off to be refitted, but I...

If your trailer has LED lights, you'll just need to add a resistor to whichever light is giving you the error.

Sorry for the long delay on posting how to enable the extra screens. Work has been beyond hectic for me lately. Here is the setting you want to change to get all the cards on Sync4. Change this value from "5" to "10", and that's it! This is located in the APIM module configuration, not the as...

I dropped my spare today to see if I could find an unused harness, or connectors without all the wires on one side, etc, and couldn't find anything.

Doesn't wireless AA work over WiFi? I'll have to try that. Hopefully not BT, then my watch will not work.

Mine is pretty stable, and works well. I am trying to figure out how to shut it off, though. I use the pro power on board a lot at work, and I'm in and out of the bed a good bit too. It's become insanely frustrating because it connects as soon as I get within 15 or 20 feet of the truck whether I...

No, those are not the options. I will post a write-up when I get home this evening!

Following. I'd love LED bulbs until I retrofit the LED tails.