Sponsored
Drayday55's latest activity
-
https://bluepilot.dev/faq/ -
Almost everything can be answered here https://bluepilot.dev/announcements/
-
Lighting is not officially supported because of the need for the resistor box. But the Q4 harness in a 2025 is confirmed to work.
-
Honestly, that is going to depend on the driver. The functionality of comma compared to bluecruise is night and day, especially since...
-
Drayday55 replied to the thread Comma AI self driver assistant.Moddded hardness
-
yeah, you would be the first person ever to have blue cruise on city streets. I would bet a comma that you don't though. Blue Cruise is...
-
Then grab a GoPro and show us a video. I've done literally thousands of hours of testing and analyzing the canbus signals of the ford...
-
Drayday55 replied to the thread Comma AI self driver assistant.I have an old one that has an intermittent fault. Works 90% of the time
-
I know, I know. I'm the jerk who is always bringing facts and logic into the room. It kills the mood, I'll try to control myself.
-
I had a feeling you'd respond with something like that. Touché. Sincerely appreciate the confirmation. I still stand by my comment...
-
They also likely don't get any meaningful data from the lightnings since they have the ICE F-150 working. It's a very small group of...
-
Actually lightning isn't listed as a supported vehicle by Comma because of this. Only ICE/Hybrid F150.
-
Drayday55 reacted to B177y's post in the thread Stick to Rotary Shift Knob Conversion w/ 3D Printed Rotary Shifter Holder with
Like.
The first post of this thread used this shifter: LX6P-7P155-HE 20 21 22 Escape Bronco sport automatic shifter gear selector. It's no... -
Quick check-in on the Lightning coupler adapter I've already sold 31 of the 50 Lightning adapters, The response has been great, and...
-
Thank u for making this list 🙏
-
I’m compiling a verified list of Ford rotary shifter part numbers. The current working theory is that part numbers starting with LX6P...
-
Drayday55 replied to the thread Just lifted 22 Lightning.I was waiting on doing some king shocks / Icons in the front. I was waiting to see if anyone would make a "kit" or trial out a gas f150...
-
Drayday55 reacted to Mike G's post in the thread Stick to Rotary Shift Knob Conversion w/ 3D Printed Rotary Shifter Holder with Like.
Personally, I don't see a reason to ever remove the center stack on a 15.5" version of the Sync screen. Those tabs up under the front...
-
Link is there on the nav bar, page will not load until 1:30pm Central https://bluepilot.dev/ Current batch is limited to the US. If...
-
Here is a sneak peek of the new dock:
-
Out of over 100 I've installed, I've had one bad 90-degree adapter. The 180-degree adapter is much more common to fail, and about 4 of...
-
Yes, The breakout boards were a great low-cost way to prototype and validate the concept, and they’ve helped a lot of people get up and...
-
I don't recall posting the final iteration of the casing on here. I believe the forum was down at the time. If you can read "Lightning"...
-
Hey all, just wanted to make a quick post for transparency, First, the waiver. I added that because, at the end of the day, this is a...
-
Drayday55 reacted to Coachmrj's post in the thread Stick to Rotary Shift Knob Conversion w/ 3D Printed Rotary Shifter Holder with Like.
I got started with an assist on the print from @Drayday55 for the rear-seated tub with a large cupholder in the front, and have just...
-
Drayday55 reacted to Mike G's post in the thread Stick to Rotary Shift Knob Conversion w/ 3D Printed Rotary Shifter Holder with Like.
So a few notes from my install today.... I actually did try to remove all the stuff needed to perform this task according to the...