2021+ F-150 FORScan List / Database / Spreadsheet ?

[C. Mays]

Sounds like you can tell the minder to shut up after one chime, but not entirely. Weird. I haven’t tried turning off the minder before.

Yeah, I used Forscan to turn off the belt minder and I can drive across the job site without it alerting me to put on the seat belt, but that’s a new one. On my 15 it was two separate changes. Thanks again. Truly appreciated.

Sponsored

 

[imnuts]

I’m trying to make the changes I can’t open the ipma I think it my Bluetooth OBD2 connector or could it be something else

I had that issue with my Bluetooth adapter as well. I could connect to every other module and make changes though. Haven't had an issue since getting a wired ODBLink Ex cable though.

 

[GolfR]

Yeah, I used Forscan to turn off the belt minder and I can drive across the job site without it alerting me to put on the seat belt, but that’s a new one. On my 15 it was two separate changes. Thanks again. Truly appreciated.

You can disable the Doo da Doo chime with

IPC 720-01-02 XXXX-X2XX

This gets rid of the startup chime but if you set this there doesn’t seem to be any way to disable the seat belt minder. Seems to be one or the other.

 

[dben18]

@Livnitup I am brand new to forscan. I have all recommended software, adapter, etc. Step 1 - I was in process of saving all my original as built modules (actually finished saving them all as stated) then noticed in the vehicle and interface information that I have a few (!) in my log. DTCs. I am wondering why this is, as I have just begun this all for the first time ever. I also wanted to state that I had an aftermarket sound system (4 new door speakers, tweeters, and 5 channel amp with 10" sub installed a year ago when I got the truck. (2021 XLT 3.5 ecoboost)... Could this be what is throwing some of these (!) (is it DTcs..?) in the "log".
DTCs in TRM: U0143:87-0B
DTCs in CCM: C1A67:97-28
DTCs in ABS: C1013:7A-68, C0031:01-28
DTCs in ACM: B1A01:13-0B, B1A02:13-0B, B1A03:13-0B, B1A04-0B

I have stopped from continuing anything until this question is answered. What are these (DTCs?) what do they mean - can this be from my aftermarket sound system and them hooking that all up. Will this hinder doing anything like disabling double honk, bambi mode, adjusting tire size (I just got 285s, 65, 20 on stock sport wheels) - relearning shift patterns, and more and more that I was excited to do?

I apologize that this is a long post, and may be in the wrong area of the forum to post. I appreciate anybody else chiming in on this all. I am open to giving my VIN if need be.

 

[dben18]

@Livnitup More information in regards to my post above. I have just found this information.^

Code: U0143 - Lost Communication With Body Control Module C
Additional Fault Symptom:
- Missing Message
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Trailer Module


Code: C1A67 - Forward Looking Sensor
Additional Fault Symptom:
- Component Or System Operation Obstructed Or Blocked
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Cruise Control
Freeze Frame :
-GLOBTIM: 0 s - Global real time
-DIST_TOT_VEH: 0.0 km - Total Vehicle Distance
-MOD_SUP_V: 0.00 V - Module Supply Voltage
-ExtTemp: 87 °C - Outside temperature


Code: C1013 - Brake System Pressure
Additional Fault Symptom:
- Fluid Leak Or Seal Failure
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Antilock braking system
Freeze Frame :
-TOTAL_TIME: 30591745 s - Total Time
-TOTAL_DIST: 16739.0 km - Total Distance
-IC_VPWR: 13.00 V - Instrument Cluster Power Supply
-AAT: 18 °C - Ambient Air Temperature
-PWR_MODE_KEY: Running (Position 2) - Power Mode Key State
-TOTAL_TIME: 30591746 s - Total Time
-TOTAL_DIST: 16739.0 km - Total Distance
-IC_VPWR: 14.25 V - Instrument Cluster Power Supply
-AAT: 18 °C - Ambient Air Temperature
-PWR_MODE_KEY: Running (Position 2) - Power Mode Key State


Code: C0031 - Left Front Wheel Speed Sensor
Additional Fault Symptom:
- General Electrical Failure
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Antilock braking system
Freeze Frame :
-TOTAL_TIME: 30572458 s - Total Time
-TOTAL_DIST: 16739.0 km - Total Distance
-IC_VPWR: 12.00 V - Instrument Cluster Power Supply
-PWR_MODE_KEY: error - Power Mode Key State
-TOTAL_TIME: 30572458 s - Total Time
-TOTAL_DIST: 16739.0 km - Total Distance
-IC_VPWR: 12.00 V - Instrument Cluster Power Supply
-PWR_MODE_KEY: error - Power Mode Key State


Code: B1A01 - Speaker #1,2,3,4
Additional Fault Symptom:
- Circuit Open
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Audio Control Module

 

[Caneman88]

Have you tried this yet? Does it work ?

Yes I have done it and it works fine just don't have soft button for cams yet but works with hard button goes to hitch view than to bed cam

 

[Canadianeh!]

Yes I have done it and it works fine just don't have soft button for cams yet but works with hard button goes to hitch view than to bed cam

Oh nice then I gotta do it. But what do you mean by soft button ?

 

[Caneman88]

Oh nice then I gotta do it. But what do you mean by soft button ?

the right side of the center touch screen

 

[Livnitup]

@Livnitup More information in regards to my post above. I have just found this information.^

The CCM DTC talking about the sensor being blocked - Did you put an aftermarket front bumper on or do anything that might be blocking the sensor that's above the driver side tow hook? Some of those DTCs seem serious but if it were me I would clear them, and see if they come back. If they do then I would take the truck to the dealership to have it diagnosed because those aren't the run-of-the-mill DTCs that pop up.

 

[Livnitup]

I want to apologize for not keeping up with this thread as I would like to but I've been getting about 50 messages, emails, etc. per day across multiple sites and have been very busy in my personal life but I hope to do a better job of keeping up soon.

I've started work on a new HVAC spreadsheet located here for anyone interested:

 

[Jesse-Infotainment]

DTCs in TRM: U0143:87-0B This is a standard DTC that even I have, there is a ssm about it

DTCs in CCM: C1A67:97-28 -

DTC Description Fault Trigger Condition CCM C1A67:97 Forward Looking Sensor: Component Or System Operation Obstructed Or Blocked Set by the CCM as a continuous memory and on-demand DTC if the CCM detects an obstruction or if the sensor is blocked. This DTC may also set when the CCM does not see a vehicle or object on the road for an extended period.

DTCs in ABS: C1013:7A-68 -

C1013:7A

Brake System Pressure: Fluid Leak Or Seal Failure

CO: ELECTRIC BRAKE BOOSTER (EBB) UNIT INTERNAL FAILURE (Anti-Lock Brake System (ABS) and Stability Control)

C0031:01-28-

C0031:01

Left Front Wheel Speed Sensor: General Electrical Failure

M: FRONT WHEEL SPEED SENSOR ELECTRICAL FAULTS (Anti-Lock Brake System (ABS) and Stability Control)

DTCs in ACM: B1A01:13-0B

B1A01:13

Speaker #1: Circuit Open

H: ONE OR MORE SPEAKER IS INOPERATIVE - ACM CONTROLLED 18 SPEAKER SYSTEM (Information and Entertainment System)

B1A02:13-0B -

B1A02:13

Speaker #2: Circuit Open

H: ONE OR MORE SPEAKER IS INOPERATIVE - ACM CONTROLLED 18 SPEAKER SYSTEM (Information and Entertainment System)

B1A03:13-0B -

B1A03:13

Speaker #3: Circuit Open

F: ONE OR MORE SPEAKER IS INOPERATIVE - ACM CONTROLLED 4, 6, 5 OR 7 SPEAKER

 

[Hectort713]

I have a question trying to get this doubt out of mind, some are stating that for the 36 Gallon tank the mods to do is

max fuel range in the IPC as
720-03-01 xxx0 00x5 54xx

But according to my 2019 Ford F-150 is the other way around

720-03-01 xxx5 54x0 00xx who here can confirm, now my 2021 Tremor has a different code

720-03-01 xxx0 00x0 00xx and I’m supposed to have the 36 Gallon extended tank, but I fill like we are not getting what it’s supposed to be.

@Livnitup
@Nightshade @tonesto7

 

[Platinum Peasant]

got this from another site:
Here's some things to try:
IPMA 706-02-02 xxxB CExx xx--
APIM 7D0-01-01 xxxx xxxx Fx--
APIM 7D0-01-02 6xxx xxxx xx--
APIM 7D0-01-04 xxxx EDxx xx--

Do an APIM reset under the wrench icon after the APIM changes.

Just did this on mine and it worked. I had my IPMA module updated earlier today

 

[Platinum Peasant]

@Jesse-Infotainment and @Livnitup huge thank you to you both for all the help you two give on these forums. Got my cameras working at speed tonight and its awesome to get some progress on this. Thank you!

 

[Platinum Peasant]

Tried it today using the 2.3.45 software and made sure to check "auto increase" in the connection tab under settings. It completed the PCM relearn with no issues. I still have code U0131 under the ABS module and IPMA module so I need to figure out what they mean.

I tried this tonight with auto increase checked, and again, was told "access denied" and then "service procedure interrupted". Not sure if im locked out somehow... maybe because its diesel and Ford locked us out so we can't delete/tune? lol.

Sponsored