ECU module programming guide using FDRS

[20ecoboost21]

Those that had the CCM fail using the Nano, when it tried updating did the ignition turn off by itself when it starts doing the Block 1 of 2 erase process cause that's what mine is doing.

Sponsored

 

[JEB]

@Jesse-Infotainment @iceman77 we have an issue. My updates were fine when installing and now I am having issues as others have indicated. Taking a drive bought it to my attention when I saw "Pre-Collision Assist Not Available". I'm getting the extra 'ML3T after whitespace and a persistent DTC U2101 and using the Mongoose, see below:

I looked up IPMA DTC U2101 in the shop manual. It provided the following description: “This continuous memory DTC sets when the IPMA As-Built data installation was not installed completely or incorrectly.“ Shop manual further says the fix is to: (1) clear the DTCs; and (2) Install IPMA As-Built data from PTS following scan tool instructions. Can you reload the as-built data via FORScan or the FDRS module configuration tool?

 

[Jesse-Infotainment]

Those that had the CCM fail using the Nano, when it tried updating did the ignition turn off by itself when it starts doing the Block 1 of 2 erase process cause that's what mine is doing.

Any update the truck is going to shut off the screen will be on

 

[Bob_Mac]

Check your as built. The as built should change. Show me just the top line of the ipma

<F10A>ML3T-14H106-AFN</F10A>

https://www.f150gen14.com/forum/threads/ecu-module-programming-guide-using-fdrs.8249/post-182800

 

[Jesse-Infotainment]

<F10A>ML3T-14H106-AFN</F10A>

https://www.f150gen14.com/forum/threads/ecu-module-programming-guide-using-fdrs.8249/post-182800

The actual as build the hex 706-01-01

Show me that line.

 

[Bob_Mac]

I looked up IPMA DTC U2101 in the shop manual. It provided the following description: “This continuous memory DTC sets when the IPMA As-Built data installation was not installed completely or incorrectly.“ Can you reload the as-built data via FORScan or the FDRS module configuration tool?

I did in both FORScan (forced) and FDRS Configuration

 

[Bob_Mac]

The actual as build the hex 706-01-01

Show me that line.

Lol... sorry.

8A50

 

[Jesse-Infotainment]

Lol... sorry.

8A50

Sorry the whole line ..

 

[Bob_Mac]

Sorry the whole line ..

<DATA LABEL="706-01-01" >
<CODE>8A50</CODE>
<CODE>A218</CODE>
<CODE>AE51</CODE>
</DATA>

I think I know where you're going with this...

 

[Jesse-Infotainment]

Well I thought I did but that is the correct change.

IF that is what the actual module is showing. Is that what it shows in Forscan?

The old config was

8A58 - A215 - 8Cxx

Not sure if you did the headlight change.. but if the new config is not working it may be an issue with the file loaded. Need to confirm the files were replaced..

The new as build is what you have except the

Xxxx - xxx8 - xxxx

That I don’t believe is standard. I is lol have to look but if I were you I’d write a as build straight from a 22 to see if the error goes away. Just that top line.

You could also write it back to what it was prior to and see if it goes away.. if it does we know you had an issue with a file

 

[Bob_Mac]

Well I thought I did but that is the correct change.

IF that is what the actual module is showing. Is that what it shows in Forscan?

The old config was

8A58 - A215 - 8Cxx

Not sure if you did the headlight change.. but if the new config is not working it may be an issue with the file loaded. Need to confirm the files were replaced..

The new as build is what you have except the

Xxxx - xxx8 - xxxx

That I don’t believe is standard. I is lol have to look but if I were you I’d write a as build straight from a 22 to see if the error goes away. Just that top line.

You could also write it back to what it was prior to and see if it goes away.. if it does we know you had an issue with a file

I did the FORScan change to Disable Auto-Reverse Braking & Alert... let me reset back to defaults

 

[Fordphanatic]

I did the FORScan change to Disable Auto-Reverse Braking & Alert... let me reset back to defaults

So your reverse brake assist is back to normal

 

[Bob_Mac]

Well I thought I did but that is the correct change.

IF that is what the actual module is showing. Is that what it shows in Forscan?

The old config was

8A58 - A215 - 8Cxx

Not sure if you did the headlight change.. but if the new config is not working it may be an issue with the file loaded. Need to confirm the files were replaced..

The new as build is what you have except the

Xxxx - xxx8 - xxxx

That I don’t believe is standard. I is lol have to look but if I were you I’d write a as build straight from a 22 to see if the error goes away. Just that top line.

You could also write it back to what it was prior to and see if it goes away.. if it does we know you had an issue with a file

Ok, we now have a serious problem and although I don't think this affects everything but, FORScan changes could make life rough when doing updates. I changed it back to the default and the error as well as the DTC are now gone!

 

[Jesse-Infotainment]

Ok, we now have a serious problem and although I don't think this affects everything but, FORScan changes could make life rough when doing updates. I changed it back to the default and the error as well as the DTC are now gone!

Wel at least it’s gone

 

[Bob_Mac]

So your reverse brake assist is back to normal

I had to revert the change back to default...

Sponsored