Comma AI self driver assistant

[UncleTony]

Probably missed it, how was 360 ohm resistor figured for reducing CAN Bus reflections at the C3X end?

It doesn't need to be at the end. It can be put wherever. But it is the correct size to place both effected CAN Buses in the correct range. There is a more detailed explanation further back in the thread.

Sponsored

 

[oafydude28]

I’ve had lots of request over the years for a dash mounted quick dock. I’ve made a prototype that will fit on the LCD of a MachE or a Lightning. In my opinion, it’s as bad as I always thought it would be, I feel like it blocks more of the road rather than less, but I want some feedback from everyone else. Is this something you would be interested in if I finish the design? It takes a lot of hours and filament to work out all the final details in a design like this, and I’m not particularly inclined to keep going unless there is strong interest.

it really can’t be any lower, there is only 5mm of bracket over the top, any less would be too weak to support the comma.

Here is what the mount looks like in the lightning. There are a few tweaks that need to be made yet. If you are on the taller side you will see that it obscures mostly the view of the hood and a small area right in front of the truck. For example in the picture from my height 6’3” you will see a cyclist visible between the comma unit and the mirror. If this was the windshield mount the cyclist would be positioned behind the comma unit. It is definitely not for everyone but it could be a nice alternative to the windshield mount.
Also thanks to Ajzride for taking on this design

 

[PJnc284]

Here is what the mount looks like in the lightning. There are a few tweaks that need to be made yet. If you are on the taller side you will see that it obscures mostly the view of the hood and a small area right in front of the truck. For example in the picture from my height 6’3” you will see a cyclist visible between the comma unit and the mirror. If this was the windshield mount the cyclist would be positioned behind the comma unit. It is definitely not for everyone but it could be a nice alternative to the windshield mount.
Also thanks to Ajzride for taking on this design

Now i just need a view from someone 9 inches shorter

 

[EVO]

setting up my coma today in my 2024 flash lightning using Uncle Tony's coupler and AJ rides windshield mount open pilot installed no problem. I uninstalled it to install blue pilot 4.0. it's just on the installing screen at 0% and never does anything. I've tried multiple reboots anybody got any ideas?

 

[EVO]

I'm using this address. installer.comma.ai/BluePilotDev/bp-4.0

 

[Ajzride]

I'm using this address. installer.comma.ai/BluePilotDev/bp-4.0

sometimes GitHub is being slow or stupid. Try a different hotspot.

 

[EVO]

I've tried att my phone. And T-Mobile my house.
Same result

 

[Ajzride]

Your URL is correct. It has to be an internet issue. It could be a regional issue. One day my GitHub was going slower than dial up.

 

[EVO]

To be more concise it says downloading for about 1 second and then it goes to installing and it stays at 0% and never moves

 

[Ajzride]

give me 30 minutes and I’ll find you an alternative URL

 

[Ajzride]

To be more concise it says downloading for about 1 second and then it goes to installing and it stays at 0% and never moves

Try 3.1 just for kicks

 

[Ajzride]

You can also try:

installer.comma.ai/alan-polk/F150

 

[EVO]

You can also try:

installer.comma.ai/alan-polk/F150

That worked, thanks!!!

 

[Ajzride]

That worked, thanks!!!

this Is just stock openpilot forced To recognize your car. I canhelp you troubleshoot more when I get home, but at least you can take a test drive now

 

[B177y]

sometimes GitHub is being slow or stupid. Try a different hotspot.

@EVO - I had to reset/reload 4.0 today and had the same issue of being stuck on 0% on the download screen while on my T-Mobile home internet. Switched to my T-mo phone hotspot and it started to download

Sponsored